Note: For width specification please know the following
Inside Mount: Measure from the inside surface to the inside surface. Please provide us with exact measurements as the manufacturer will make the necessary deduction of 3/8” off of the fabric.
Outside Mount: Measure the exact area you wish to cover as the manufacturer will produce your shade to your exact measurements. Be sure to take the window trim into account.
General Specifications (unless otherwise specified under certain specifications)
Installation Brackets
|
Blind Width |
# of Brackets |
|
Up to 38” |
2 |
|
38”-68” |
3 |
|
68”-82” |
4 |
|
82”-106” |
5 |
|
106”-130” |
6 |
|
130” and above |
7 |
Quantity of Cords
|
Blind Width |
# of Cords |
|
Up to 44” |
2 |
|
44 1/8”-80” |
3 |
|
80 1/8”-116” |
4 |
|
116 1/8”-144” |
5 |
Stacking Chart: This chart represents the amount of the shade that is gathered at the top of window when fully raised. The measurements in this chart includes the stack of the fabric, the headrail, and the bottomrail.
|
Shade Height |
To 36” |
To 48” |
To 60” |
To 72” |
To 84” |
To 96” |
To 108” |
To 120” |
To 132” |
To 144” |
|
Stacking Height |
1 7/8” |
2 1/8” |
2 ½” |
2 13/16” |
3 1/16” |
3 3/8” |
3 11/16” |
4” |
4 15/16” |
4 5/8” |
Standard Shade Specifications (This is for standard shade only, please see specifications for special options as they may be different than the standard shade availability)
Width: 6” – 144”
Height: 6” – 144”
Headrail Dimensions: 1.81”w x 0.52”h
Bottomrail Dimensions: 1.48”w x 0.43”h
Mounting Requirements
- Flush Mount: 2 ¼” Depth
- Mounting Depth for Standard: 5/8”
Top Down/Bottom Up
Width: 12” – 72”
Height: 12” – 96”
Controls: Left controls lift from the bottom. Right controls lower from the top. Reverse controls are not available.
Top Down Only
Width: 12” – 72”
Height: 12” – 96”
Continuous Cord Loop System
Width: 18” – 144”
Height: 6” – 144”
- If width is greater than 120”, the maximum height is 96”
- If width is less than 30”, the maximum height is 96”
- This feature is not available with top down, top down/bottom up, day/night shades, angle top/bottom shades, or skylights.
- For 2 on 1 Headrail, controls will be located on the left side of the left shade, and the right side of the right shade.
Headrail Dimensions: 1.78”w x 1.35” h
Bottomrail Dimensions: 1.72”w x 0.58”h
Flush Mount Minimum Depth: 2 1/8”
Stacking Chart- Including Headrail and Bottomrail
|
Approximate Shade Height |
36” |
48” |
60” |
72” |
84” |
96” |
108” |
120” |
132” |
144” |
|
Stack Height |
2 13/16” |
3” |
3 5/16” |
3 5/8” |
3 15/16” |
4 ¼” |
4 ½” |
4 13/16” |
5” |
5 7/16” |
Cord Loop Lengths
|
Blind Width |
Cord Length |
|
18” – 48” |
24” |
|
48 1/8” – 60” |
36” |
|
60 1/8” – 72” |
48” |
|
72 1/8” – 96” |
72” |
|
96 1/8” – 119 7/8” |
96” |
|
120” and above |
120” |
Cordless
Width: 13” – 120”
Height: 12” – 78”
- If the width is less than 30”, the maximum height is 76”
Headrail Dimensions: 1.78”w x 1.35” h
Bottomrail Dimensions: 1.72”w x 0.58”h
Flush Mount Minimum Depth: 2 1/8”
Stacking Chart- Including Headrail and Bottomrail
|
Approximate Shade Height |
36” |
48” |
60” |
72” |
84” |
96” |
108” |
120” |
132” |
144” |
|
Stack Height |
2 13/16” |
3” |
3 5/16” |
3 5/8” |
3 15/16” |
4 ¼” |
4 ½” |
4 13/16” |
5” |
5 7/16” |
Cordless Top Down/Bottom Up
Width: 22 ½” – 60”
Height: 12” – 78”
- If width is less than 30”, the maximum height is 76”
- Skylight pole can be purchased separately to raise and lower shades that are hard to reach.
Mounting Depth for Standard: ½”
2-on-1 Headrail
Standard Shade
Width: 12” – 144”
Height: 6” – 144”
Cordless Shade
Width: 25” – 120”
Height: 12” – 78”
If the width is less than 30”, the maximum height is 76”
How to Measure for a 2-on-1 Headrail:
Outside Mount:
- Overall Shade Width: Measure the desired width
- Levolor recommends that you add 3” to the overall width of the window for complete coverage. For maximum privacy, add an additional 3” to the total width of the window.
- Left Shade Width: Measure the width that you want the left shade to cover
- Right Shade Width: Measure the width that you want the right shade to cover
- The left shade width plus the gap, plus the right shade width must equal the overall shade width.
- Height: Measure the desired height
- Levolor recommends that you add at least 3” to the height of the window for complete coverage. For maximum privacy, add an additional 3” to the total height of the window.
- Order the left shade first (This is shade 1)
- Note: There will be a ¼” innerspace between the fabric on the left and right shade to allow for shades to operate independently. This standard innerspace can be increased if customer requests, however the minimum is ¼”
Inside Mount:
- Overall Shade Width: Measure the window’s width at the top, middle, and bottom. Order the narrowest measurement.
- Left Shade Width: Measure the width that you want the left to cover.
- Right Shade Width: Measure the width that you want the right to cover.
- Height: Measure the window from the top to the bottom for desired height
- Order the left shade first (This is shade 1)
Note: There will be a ¼” gap between the fabric on the left and right shade